8613851491524
info@ckracking.com
enLanguage
Search
Products
Home / Products / Automated Long Material Storage System / Details
6 m Gantry Storage System For Bundled Long Materials, 3,000 kg Rated Load
video
6 m Gantry Storage System For Bundled Long Materials, 3,000 kg Rated Load

6 m Gantry Storage System For Bundled Long Materials, 3,000 kg Rated Load

CK METAL STORAGE SOLUTIONS prepares this 6 m gantry storage system for plants that keep long material in defined bundles or carriers before the next production step. The usual 6 m configuration is rated at 3,000 kg (6,600 lb) per storage unit. That rating is a starting point for layout, not approval for every bundle: carrier tare, bundle geometry, center of load, support points and restraint must be defined together.
·6 m (19.7 ft) is the typical material length, not the final building or carrier length.
·3,000 kg (6,600 lb) is a typical storage-unit rating; confirm whether carrier tare is included.
·Fixed or mobile rack bases change aisle access. The cantilever arms themselves do not extend.
·Whole storage units move through the gantry system; this page does not promise single-bar feeding.
Send Inquiry

Choose a storage unit before relying on the 3,000 kg rating

 

A bundled-long-material storage plan works when the bundle, carrier and restraint method are treated as one storage unit. A total weight alone does not show whether a bundle is stable on the supports or whether its center of load remains acceptable during transfer. Send the packed cross-section, bundle length, heaviest unit and carrier tare with the quotation request.

 

The 6 m figure describes the typical material length. It does not include a carrier allowance, end clearance, receiving space or the travel envelope for the gantry. A layout drawing must establish those dimensions after the bundle and handoff position are known.

 

Specification

Typical page basis

What must be confirmed

Material length

6 m (19.7 ft)

Actual stock length, overhang and carrier allowance

Rated storage unit

3,000 kg (6,600 lb)

Carrier tare, load distribution and approved loading pattern

System maximum

Up to 5,000 kg (11,000 lb)

Project configuration; do not apply it to this 6 m unit without engineering approval

Rack arrangement

Fixed or mobile cantilever bases

Aisle sequence, rail interface, clearances and exclusion area

Load ratings and layout suitability depend on the approved carrier, support and operating arrangement.

Illustrative wide view of a gantry retrieving a defined long-material storage unit

 

Keep bundle restraint and downstream handoff separate from gantry storage

 

The gantry stores and retrieves an agreed carrier or storage unit. It does not establish a universal bundle restraint method or turn a stored bundle into a single-bar supply system. If a saw, drill line or machining cell needs individual pieces, define who removes material at the transfer point and how unused material returns to storage.

 

Receiving should use the same unit definition as storage. If incoming bundles vary in width, wrapping, dunnage or length, identify those differences before a rack and carrier layout is released. This prevents a nominal 3,000 kg total from concealing a support or restraint issue.

 

Fixed and mobile racks answer different access questions

 

Fixed cantilever racks with a gantry keep permanent aisles between rack groups. They suit operations that need several stable access lanes. Mobile cantilever racks with a gantry move complete rack rows on rail-guided bases to open one shared operating aisle. They suit layouts where permanent aisle area is the larger constraint.

 

Neither arrangement uses roll-out or telescopic cantilever arms. In a mobile layout, the bases and full rack rows move; the arms remain ordinary fixed cantilever arms.

 

 

Decision point

Fixed racks with gantry

Mobile racks with gantry

Access pattern

Permanent aisles between groups

One aisle opened when required

What moves

Gantry and agreed storage unit

Gantry, agreed storage unit and complete rack rows on bases

Best question to ask

Do several lanes need regular access?

Can the retrieval sequence use one shared aisle?

 

Alternative wide illustrative view of a gantry and cantilever racks for long-material storage

 

Plan the handoff zone and the operating envelope together

 

Start the layout from the receiving and transfer point, then map the carrier path through the rack area. The engineering review needs the lowest overhead obstruction, column grid, floor information, rail route, receiving position and downstream handoff. The known product information confirms a gantry height of up to 10 m and rack heights of 7 to 8 m, but it does not supply an installation dimension for this bundle application.

 

A good fit is a plant that stores repeated bundle formats and can define the carrier and restraint method before ordering. It is not the right choice when bundles change without a controlled storage-unit definition, or when the next process requires automatic single-piece feeding that has not been specified.

 

FAQ

 

Q: Does 3,000 kg mean every long-material bundle is accepted?

A: No. The 3,000 kg figure is a typical storage-unit rating. The carrier tare, bundle shape, support positions, restraint and center of load must be reviewed for the approved configuration.

Q: Can the system feed one bar at a time to a machine?

A: Not from the confirmed information. The system retrieves an agreed storage unit. Define any single-piece removal or machine interface separately.

Q: Does a 6 m material length define the building size?

A: No. Carrier allowance, handling clearance, gantry travel and the receiving area must be added in the layout drawing.

Q: Do the cantilever arms extend?

A: No. The confirmed system uses ordinary fixed cantilever arms. In a mobile layout, complete rack rows move on their bases to open a shared aisle.

 

Request a bundle-storage layout

 

Send the maximum material length, heaviest full bundle, bundle cross-section, carrier tare, restraint method, receiving position and a plan of the available floor area. CK METAL STORAGE SOLUTIONS will use these inputs to prepare a layout discussion and define the storage-unit basis for quotation.

 

See our contact page to request a layout discussion. For broader system background, read CK METAL STORAGE SOLUTIONS automated profile storage information.

 

Hot Tags: 6 m gantry storage system for bundled long materials, 3,000 kg rated load, China 6 m gantry storage system for bundled long materials, 3,000 kg rated load manufacturers, suppliers, factory

Send Inquiry